A practical guide to rings, necklaces, bracelets, and earrings
The right size affects more than whether a piece can be worn. It also shapes where the jewelry rests, how closely it sits, and how it looks in proportion to you. A few minutes of measuring before you order can be more reliable than choosing from your usual size alone.
The methods below are useful for measuring at home. Your final choice should always be based on the dimensions, construction, and adjustable range shown on the individual product page.
Before You Measure
A flexible measuring tape is the easiest tool to use. If you do not have one, wrap a strip of non-stretch paper or string around the area, mark where the ends meet, and lay it flat against a ruler.
Do not pull the tape or paper too tightly. Measure rings and bracelets twice; if the results differ, take a third measurement. Fingers and wrists can change slightly with temperature and activity, so avoid relying on a single measurement when your hands are noticeably cold, warm, or swollen.
Write down the unit with every measurement. Product pages may use millimeters, centimeters, or inches. For reference, 10 mm equals 1 cm, and 1 inch equals 2.54 cm.
How to Measure Your Ring Size
If you own a ring that already fits the intended finger, measure its inside diameter. Place the ring flat on a ruler and measure from one inside edge to the other, without including the metal itself. Record the result in millimeters and compare it with the measurements on the product page.
For the most reliable result, use a professional ring sizer or ask a local jeweler to measure the intended finger. This is especially helpful for a wide band, a ring that must pass over a larger knuckle, or a size that falls between two options.
If you do not have a suitable ring, gently wrap a strip of non-stretch paper around the finger where the ring will sit. Mark the point where the paper meets, then measure from the starting edge to the mark. This number is the finger circumference, not the ring diameter, so the two measurements should not be treated as the same value.
The same finger can differ between your left and right hands, and a wide band usually feels closer than a fine band. Check the band width and product notes as well as the size name. If your measurement falls between two available options, contact us about the construction of that particular ring before choosing from a general chart.
Measure twice and use the measurements on the individual product page as your final reference.
This conversion chart is a reference. Ring width and construction can change how a size feels.
How to Choose a Necklace Length
The clearest reference is a necklace you already own and like. Lay it flat, straighten the chain, and measure from one end of the clasp to the other.
You can also place a flexible tape around your neck and let it fall to the point where you would like the necklace to rest. If the design includes a pendant, remember that the pendant will extend below the chain.
Common necklace lengths offer a useful visual starting point:
- About 16 inches (40.6 cm) often sits near the base of the neck.
- About 18 inches (45.7 cm) often rests around the collarbone.
- About 20 inches (50.8 cm) usually falls a little below the collarbone.
- About 24 inches (61 cm) generally sits lower on the chest.
These positions are approximate. Neck circumference, height, neckline, pendant size, and layering can all change where a necklace appears to fall. If a piece includes an extender, check both the main chain length and the full adjustable range.
How to Measure Your Bracelet Size
Wrap a flexible tape around the place where you plan to wear the bracelet, usually near the wrist bone. Let the tape rest against the skin without pulling it tight. A strip of non-stretch paper or string can be used in the same way and then measured against a ruler.
Add a little room to your wrist measurement according to how you prefer the bracelet to sit. These allowances are starting points rather than universal rules:
- Close fit: add about 0.25–0.5 inch (0.6–1.3 cm).
- Comfortable everyday fit: add about 0.5–0.75 inch (1.3–1.9 cm).
- Relaxed fit: add about 0.75–1 inch (1.9–2.5 cm).
Chain bracelets, rigid bangles, and open cuffs fit differently. For a rigid or open design, also check the inside diameter, opening width, and the wearing instructions on the product page. Total bracelet length alone may not describe how the piece will pass over or sit on your hand.
How to Consider Earring Size and Weight
Earrings do not usually have a traditional size, but their length, width, and weight can make a noticeable difference to both proportion and feel.
In front of a mirror, hold a ruler downward from the piercing and note where the listed length is likely to end. You can also compare the measurements with a pair you wear regularly. For hoop earrings, check whether the product page lists the inside or outside diameter.
If you are sensitive to weight, look for the weight of one earring on the product page. Earlobes, piercing positions, and personal tolerance vary, so an image alone cannot show how heavy an earring will feel. If the weight is not listed, send us the product link and we can check the available product information.
Details That Are Easy to Miss
Many sizing mistakes come from the measuring method rather than the number itself:
- Measuring the outside of a ring instead of its inside diameter.
- Using elastic string or another material that stretches.
- Measuring only once and overlooking temperature, left-to-right hand differences, or the exact wearing position.
- Choosing from an S, M, L, or US size label without checking millimeters, diameter, circumference, or total length.
- Forgetting to include an extender, opening, band width, or pendant length.
- Rechecking the size only after production has begun for a custom, engraved, or otherwise return-restricted piece.
For custom jewelry, confirm the final measurement in writing before production begins. You can also share the jewelry type, measurements, and preferred fit through our Atelier inquiry page.
A Final Check Before Ordering
Before adding a piece to your cart, ask yourself:
- Did I measure the exact place where I intend to wear it?
- Am I comparing the same unit used on the product page?
- Does the size refer to inside diameter, circumference, or total length?
- Have I checked for an extender, opening, or other adjustable detail?
- If the piece is custom or return-restricted, have I confirmed the size before ordering?
If you are still unsure, use our Contact page or email support@vyloren.store. Include the product link, your measurements, and whether you prefer a close, comfortable, or relaxed fit. We can then help you check the information for that particular design.